Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Placing the plan above the front view in first angle projection"
Practice set: Enlarge and reduce plane figures based on the ratio of areas and verify the result
Set me five practice tasks on enlarge and reduce plane figures based on the ratio of areas
Subscribe to unlock allLet me explain: 3. Explain why triangles on the same base and between the same parallels are equal in area
I am going to explain 3. Explain why triangles on the same base and between the same paral
Subscribe to unlock allProject task: That the tangent is perpendicular to the radius at the point of contact. Students construct
Set me a small project on that the tangent is perpendicular to the radius at the point of
Subscribe to unlock allLet me explain: 2. Construct an ellipse by the four-centre, concentric-circles and parallelogram methods
Let me talk you through 2. Construct an ellipse by the four-centre, concentric-circles and
Subscribe to unlock allLet me explain: 3. Determine true lengths of the edges of full and truncated solids
I am going to explain 3. Determine true lengths of the edges of full and truncated solids
Subscribe to unlock allSpot my mistake: 4. Distinguish chain, parallel and running dimensioning and select the appropriate system
Give me a wrong or muddled explanation of 4. Distinguish chain, parallel and running dimen
Subscribe to unlock allQuiz: 2. Construct isometric circles as four-centre ellipses in all three isometric planes
I am revising Isometric Drawing II for SS1 Technical Drawing. Test me on 2. Construct isom
Subscribe to unlock allProject task: Building a composite object in isometric from three orthographic views
Give me a practical task on building a composite object in isometric from three orthograph
Subscribe to unlock allPractice set: Producing a composite isometric drawing from orthographic views
Set me five practice tasks on producing a composite isometric drawing from orthographic vi
Subscribe to unlock allWAEC prep: The two classifications of drawing, compared
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: all letters within ±0.5 mm of the guide-line height with uniform stroke thickness
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Demonstrate safe handling of the drawing board, T-square and compass
Be my SS1 Technical Drawing teacher for this one point: 1. Demonstrate safe handling of th
Subscribe to unlock allQuiz: 2. Identify hazards in the drawing studio
Quiz me on 2. Identify hazards in the drawing studio, from the SS1 Technical Drawing topic
Subscribe to unlock allQuiz: 2. Produce lines with the correct weights
I am revising Lines and Line Work for SS1 Technical Drawing. Test me on 2. Produce lines w
Subscribe to unlock allReal-life Nigeria: Each line type against the standard line chart. Students produce a reference sheet showing all
Show me how each line type against the standard line chart. Students produce a reference s
Subscribe to unlock allWAEC prep: Success: division into seven parts accurate to within 0.5 mm across the whole line
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Constructing the special angles without a protractor
Set me five practice tasks on constructing the special angles without a protractor, at the
Subscribe to unlock allSpot my mistake: Given two sides and the included angle
Show me a worked example on given two sides and the included angle with an error somewhere
Subscribe to unlock allQuiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allSpot my mistake: Success: all three constructions within 0.5 mm and ±1° of the specified data
Show me a worked example on success: all three constructions within 0.5 mm and ±1° of the
Subscribe to unlock all