Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →196 prompts matching "Drawing to 1:10 a vertical section through a strip foundation"
Spot my mistake: 4. Divide a straight line into any number of equal segments and into a given ratio
Write a short SS1 Technical Drawing answer about 4. Divide a straight line into any number
Subscribe to unlock allWAEC prep: Success: division into seven parts accurate to within 0.5 mm across the whole line
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allWAEC prep: Constructing eccentric and concentric circles to specification
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 3. Describe an escribed circle and construct one to a given triangle
Be my SS1 Technical Drawing teacher for this one point: 3. Describe an escribed circle and
Subscribe to unlock allQuiz: 4. Explain the geometric basis of each construction using bisectors
Quiz me on 4. Explain the geometric basis of each construction using bisectors, from the S
Subscribe to unlock allPractice set: Incentre construction using angle bisectors
Give me a practice set on incentre construction using angle bisectors for SS1 Technical Dr
Subscribe to unlock allWAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 3. Construct the special quadrilaterals to given dimensions
You are my personal SS1 Technical Drawing tutor. Teach me 3. Construct the special quadril
Subscribe to unlock allSpot my mistake: 2. Identify standard line types and their applications as set out in the drawing standard
Write a short SS1 Technical Drawing answer about 2. Identify standard line types and their
Subscribe to unlock allPractice set: Success: both projection symbols drawn to correct proportion and correctly identified
Set me five practice tasks on success: both projection symbols drawn to correct proportion
Subscribe to unlock allLet me explain: Consolidation of drawing practice, line work
I am going to explain consolidation of drawing practice, line work to you, as an SS1 Techn
Subscribe to unlock allReal-life Nigeria: Naming polygons from three to twelve sides
Take naming polygons from three to twelve sides out of the textbook. Describe a real Niger
Subscribe to unlock allTeach me: 1. Describe the uses of scale in technical drawing
I am an SS1 student studying Scales in Technical Drawing. Explain 1. Describe the uses of
Subscribe to unlock allLet me explain: 3. Construct a plain scale to a given representative fraction
I am going to explain 3. Construct a plain scale to a given representative fraction to you
Subscribe to unlock allWAEC prep: Success: all five scale-factor calculations correct to two decimal places
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 2. Construct a rectangle equal in area to a given triangle
Be my SS1 Technical Drawing teacher for this one point: 2. Construct a rectangle equal in
Subscribe to unlock allQuiz: 3. Construct a square equal in area to a given rectangle
Quiz me on 3. Construct a square equal in area to a given rectangle, from the SS1 Technica
Subscribe to unlock allTeach me: 2. Construct a tangent to a circle at a point on its circumference and from an external point
You are my personal SS1 Technical Drawing tutor. Teach me 2. Construct a tangent to a circ
Subscribe to unlock allQuiz: 3. Construct an arc tangent to a straight line
I am revising Tangents and Tangency I for SS1 Technical Drawing. Test me on 3. Construct a
Subscribe to unlock all