Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →215 prompts matching "Determine the lines of intersection of two regular prisms meeting at 90 degrees"
Spot my mistake: 4. Divide a straight line into any number of equal segments and into a given ratio
Write a short SS1 Technical Drawing answer about 4. Divide a straight line into any number
Subscribe to unlock allReal-life Nigeria: Each line type against the standard line chart. Students produce a reference sheet showing all
Show me how each line type against the standard line chart. Students produce a reference s
Subscribe to unlock allPractice set: Each construction step by step on the board. Students construct the full set of special angles
Give me a practice set on each construction step by step on the board. Students construct
Subscribe to unlock allLet me explain: Consolidation of drawing practice, line work
I am going to explain consolidation of drawing practice, line work to you, as an SS1 Techn
Subscribe to unlock allLet me explain: 3. Construct a regular polygon using the diagonal method
Let me talk you through 3. Construct a regular polygon using the diagonal method from the
Subscribe to unlock allLet me explain: 3. Describe the applications of enlargement and reduction in design and manufacture
Act as my study partner. I will teach you 3. Describe the applications of enlargement and
Subscribe to unlock allSpot my mistake: 1. Construct an arc of given radius internally touching two circles
Write a short SS1 Technical Drawing answer about 1. Construct an arc of given radius inter
Subscribe to unlock allTeach me: 2. Construct an arc of given radius externally enclosing two circles
I am an SS1 student studying Tangents and Tangency II in Technical Drawing. Explain 2. Con
Subscribe to unlock allLet me explain: 4. Blend arcs and lines smoothly, marking all points of tangency
I am going to explain 4. Blend arcs and lines smoothly, marking all points of tangency to
Subscribe to unlock allPractice set: Cavalier and cabinet oblique of the same block so students can see the halved receding depth.
Give me a practice set on cavalier and cabinet oblique of the same block so students can s
Subscribe to unlock allLet me explain: 3. State the advantages of CADD over manual drawing
Let me talk you through 3. State the advantages of CADD over manual drawing from the Drawi
Subscribe to unlock allLet me explain: 3. Describe the purpose of lettering
I am going to explain 3. Describe the purpose of lettering to you, as an SS1 Technical Dra
Subscribe to unlock allProject task: Layout of a title block on the board with proportions marked. Students draw a border
Give me a practical task on layout of a title block on the board with proportions marked.
Subscribe to unlock allTeach me: 1. Demonstrate safe handling of the drawing board, T-square and compass
Be my SS1 Technical Drawing teacher for this one point: 1. Demonstrate safe handling of th
Subscribe to unlock allQuiz: 2. Produce lines with the correct weights
I am revising Lines and Line Work for SS1 Technical Drawing. Test me on 2. Produce lines w
Subscribe to unlock allWAEC prep: Success: division into seven parts accurate to within 0.5 mm across the whole line
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 2. Identify the types of angles: acute, right, obtuse, reflex, complementary and supplementary
Set me a quick recall test on 2. Identify the types of angles: acute, right, obtuse, refle
Subscribe to unlock allSpot my mistake: Given two sides and the included angle
Show me a worked example on given two sides and the included angle with an error somewhere
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Success: all three constructions within 0.5 mm and ±1° of the specified data
Show me a worked example on success: all three constructions within 0.5 mm and ±1° of the
Subscribe to unlock all