Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →216 prompts matching "Calculating the true length of a line whose plan is 60 mm"
Teach me: 1. Define technical drawing in your own words and distinguish the two classifications of drawing
You are my personal SS1 Technical Drawing tutor. Teach me 1. Define technical drawing in y
Subscribe to unlock allLet me explain: 3. State the advantages of CADD over manual drawing
Let me talk you through 3. State the advantages of CADD over manual drawing from the Drawi
Subscribe to unlock allLet me explain: 3. Describe the purpose of lettering
I am going to explain 3. Describe the purpose of lettering to you, as an SS1 Technical Dra
Subscribe to unlock allSpot my mistake: 4. Divide a straight line into any number of equal segments and into a given ratio
Write a short SS1 Technical Drawing answer about 4. Divide a straight line into any number
Subscribe to unlock allReal-life Nigeria: Each line type against the standard line chart. Students produce a reference sheet showing all
Show me how each line type against the standard line chart. Students produce a reference s
Subscribe to unlock allLet me explain: 1. State the purpose of drawing standards
Let me talk you through 1. State the purpose of drawing standards from the Drawing Standar
Subscribe to unlock allSpot my mistake: Formal assessment of the first term programme of study
Give me a wrong or muddled explanation of formal assessment of the first term programme of
Subscribe to unlock allTeach me: 1. Enlarge a given plane figure based on a ratio of areas
You are my personal SS1 Technical Drawing tutor. Teach me 1. Enlarge a given plane figure
Subscribe to unlock allQuiz: 2. Reduce a given plane figure based on a ratio of areas
I am revising Enlargement and Reduction II for SS1 Technical Drawing. Test me on 2. Reduce
Subscribe to unlock allLet me explain: 3. Apply the radial (ray) method of enlargement from a chosen pole
Let me talk you through 3. Apply the radial (ray) method of enlargement from a chosen pole
Subscribe to unlock allProject task: That the tangent is perpendicular to the radius at the point of contact. Students construct
Set me a small project on that the tangent is perpendicular to the radius at the point of
Subscribe to unlock allTeach me: Formal assessment of the second term programme of study
You are my personal SS1 Technical Drawing tutor. Teach me formal assessment of the second
Subscribe to unlock allWAEC prep: The two classifications of drawing, compared
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allProject task: Layout of a title block on the board with proportions marked. Students draw a border
Give me a practical task on layout of a title block on the board with proportions marked.
Subscribe to unlock allTeach me: 1. Demonstrate safe handling of the drawing board, T-square and compass
Be my SS1 Technical Drawing teacher for this one point: 1. Demonstrate safe handling of th
Subscribe to unlock allQuiz: 2. Produce lines with the correct weights
I am revising Lines and Line Work for SS1 Technical Drawing. Test me on 2. Produce lines w
Subscribe to unlock allWAEC prep: Success: division into seven parts accurate to within 0.5 mm across the whole line
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 2. Identify the types of angles: acute, right, obtuse, reflex, complementary and supplementary
Set me a quick recall test on 2. Identify the types of angles: acute, right, obtuse, refle
Subscribe to unlock allPractice set: Each construction step by step on the board. Students construct the full set of special angles
Give me a practice set on each construction step by step on the board. Students construct
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock all