Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →284 prompts matching "4. Compare the three methods for accuracy"
Project task: Set out a segmental arch of 900 mm span
Set me a small project on set out a segmental arch of 900 mm span, the kind I could finish
Subscribe to unlock allQuiz: Straight-flight, quarter-turn, half-turn or dog-leg, and geometrical or spiral staircases
Quiz me on straight-flight, quarter-turn, half-turn or dog-leg, and geometrical or spiral
Subscribe to unlock allTeach me: Preparing to 1:10 a detailed vertical section through a strip foundation
You are my personal SS2 Technical Drawing tutor. Teach me preparing to 1:10 a detailed ver
Subscribe to unlock allTeach me: Assessed AO3, and detailed building drawing is a standing WAEC and NECO question
I am an SS2 student studying Building Details I in Technical Drawing. Explain assessed AO3
Subscribe to unlock allQuiz: Assessed AO2, and roof types and members recur in WAEC and NECO
Quiz me on assessed AO2, and roof types and members recur in WAEC and NECO, from the SS2 T
Subscribe to unlock allPractice set: Tension and compression members on a board sketch of a king post truss
Give me a practice set on tension and compression members on a board sketch of a king post
Subscribe to unlock allProject task: Roll a tin lid along a straight edge and plot
Give me a practical task on roll a tin lid along a straight edge and plot from Loci and Sp
Subscribe to unlock allWAEC prep: Four special curves
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: In two sentences why a parabolic dish concentrates a signal at a single point
Show me a worked example on in two sentences why a parabolic dish concentrates a signal at
Subscribe to unlock allSpot my mistake: Constructing a hyperbola from given foci and a constant difference of 30 mm
Give me a wrong or muddled explanation of constructing a hyperbola from given foci and a c
Subscribe to unlock allSpot my mistake: Constructing a cycloid generated by a 40 mm diameter circle rolling along a straight line
Show me a worked example on constructing a cycloid generated by a 40 mm diameter circle ro
Subscribe to unlock allReal-life Nigeria: Constructing an involute of a circle and a cycloid on one A3 sheet
Take constructing an involute of a circle and a cycloid on one A3 sheet out of the textboo
Subscribe to unlock allSpot my mistake: Two products that use an involute profile
Show me a worked example on two products that use an involute profile with an error somewh
Subscribe to unlock allProject task: Round scissors, pliers, a bicycle brake caliper
Give me a practical task on round scissors, pliers, a bicycle brake caliper from Link Mech
Subscribe to unlock allSpot my mistake: Drawing a four-bar linkage to given link lengths and set out twelve crank positions
Give me a wrong or muddled explanation of drawing a four-bar linkage to given link lengths
Subscribe to unlock allWAEC prep: Develop and build in card a truncated cylinder of 50 mm diameter cut at 45 degrees
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allLet me explain: Why two solids meeting produce a line or curve of intersection
Let me talk you through why two solids meeting produce a line or curve of intersection fro
Subscribe to unlock allLet me explain: Assessed AO3, and intersecting cylinders appear in WAEC and NECO Paper 2
I am going to explain assessed AO3, and intersecting cylinders appear in WAEC and NECO Pap
Subscribe to unlock allSpot my mistake: Labelling five terms on a given perspective layout
Show me a worked example on labelling five terms on a given perspective layout with an err
Subscribe to unlock allQuiz: Drawing a circle in perspective by enclosing it in a square and plotting eight points
Set me a quick recall test on drawing a circle in perspective by enclosing it in a square
Subscribe to unlock all